Welcome, Guest. Please Login 3dfx Archive
 
  HomeHelpSearchLogin  
 
Pages: 1 2 
Send Topic Print
V5500 heatsink tutorial. (Read 556 times)
paulpsomiadis
God Member
*****
Offline


-=3Dfx still rox!=-

Posts: 2011
Newcastle U.K.
Gender: male
V5500 heatsink tutorial.
16.05.07 at 18:36:11
 
Due to the MANY, MANY times people ask about this in the forum...

A tutorial about heatsink modding on the V5500

Part 1
====

1. Find a see-through polythene bag.
2. Place V5500 into bag and push all the air out the bag.
3. Seal bag with tape.
4. Put into freezer and leave overnight.

Part 2
====

1. Find a small flat ended screwdriver.
2. Remove bag from freezer.
3. Rip open bag and QUICKLY and CAREFULLY do the following...
4. Put the screwdriver under one edge of a heatsink and gently pry it off (put a credit card or something similar between the screwdriver and the PCB so you don't damage tracks).
5. Repeat with other heatsink.
(being careful not to knock off resistors, etc...)
6. While the card is still partially frozen - use a stanley knife to scrape off the remaining glue on the VSA-100 chips.
7. Use some fine grit sandpaper to remove the leftover small bits of glue.

Part 3 (tips)
========

For heatsink compound - I'd recommend ARCTIC ALUMINA (it's best to use non-electrically conductive compounds if you're a noob, as they will not accidentally short-out components)

Heatsinks...I'd recommend anything by THERMALTAKE...

Be sure you get heatsinks that hace removable fans - so if the fan fails it can be replaced at a later date.

When spreading the compound on the GPU's and RAM chips, use ONLY enough to cover the chips BARELY - remember you're not icing a cake!

That's all folks!

Good luck and BE CAREFUL - try not to total your V5500 in the process!
Back to top
« Last Edit: 17.05.07 at 22:25:39 by paulpsomiadis »  

-=To MOD or not to MOD, that is a DUMB question - just MOD it!=-&&&&+May God stand between you and harm in all the empty places you must walk.+
themadhaxor  
IP Logged
 
Chosen_One
Senior Member
****
Offline


Keeper of the BIOS-files...

Posts: 499
Germany
Gender: male
Re: V5500 heatsink tutorial.
Reply #1 - 16.05.07 at 19:09:33
 
artic silver is NOT electroconductive...by the way Wink
Back to top
 
WWW  
IP Logged
 
Eye-Q
God Member
*****
Offline



Posts: 522
Germany
Gender: male
Re: V5500 heatsink tutorial.
Reply #2 - 16.05.07 at 19:20:08
 
Quote:
4. Put the screwdriver under one edge of a heatsink and gently pry it off (reasonable force required).

There should be a credit card or something similar between the screwdriver and the PCB so the screwdriver doesn't harm the traces when you pop off the heatsinks.
Back to top
 
 
IP Logged
 
NitroX infinity
YaBB Moderator
*****
Offline



Posts: 1936
The Netherlands
Gender: male
Re: V5500 heatsink tutorial.
Reply #3 - 17.05.07 at 12:02:09
 
Part 1 is optional, I didn't do it.
Also, Gary has a video on his site about this.
Back to top
 
WWW  
IP Logged
 
MrFossey
Junior Member
**
Offline


\o/

Posts: 76
Re: V5500 heatsink tutorial.
Reply #4 - 17.05.07 at 13:04:48
 
Personally I don't use fridge methods, too. Though I didn't remove heatsinks from VSA-100 chips, I did from other cards (including the Voodoo3 which is probably easier because of the softer conductive material) which had a hard epoxy too. Just lift it up with a screwdriver. Be sure to protect the card itself by using an old creditcard (or something) just like G. Donovan did in the video with the V5 6000.
Back to top
 
 
IP Logged
 
elfuego
Senior Member
****
Offline


Searching for V5 6k...

Posts: 420
Aachen, Deutschland
Gender: male
Re: V5500 heatsink tutorial.
Reply #5 - 17.05.07 at 18:14:03
 
This is the first time I hear about fridge method, I heard about something else.

The guru's on my forum advice to use the card intensively in 3D mode for 30minutes, then turn off computer, remove the card from the slot and promtly remove the heatsink in the way described. That's the opposite method Smiley

Anyway - be careful!
Back to top
 
278277112  
IP Logged
 
BFG3dfx
Ex Member


Re: V5500 heatsink tutorial.
Reply #6 - 17.05.07 at 20:45:26
 
i use the freezer myself, cold makes the glue brittle, hot you would think would make is soft i guess  Undecided
Back to top
 
 
IP Logged
 
paulpsomiadis
God Member
*****
Offline


-=3Dfx still rox!=-

Posts: 2011
Newcastle U.K.
Gender: male
Re: V5500 heatsink tutorial.
Reply #7 - 17.05.07 at 22:25:59
 
Corrections made... Wink
Back to top
 

-=To MOD or not to MOD, that is a DUMB question - just MOD it!=-&&&&+May God stand between you and harm in all the empty places you must walk.+
themadhaxor  
IP Logged
 
ultima
God Member
*****
Offline


Always searching

Posts: 876
The Netherlands
Gender: male
Re: V5500 heatsink tutorial.
Reply #8 - 18.05.07 at 13:01:28
 
I used the freeze method on my 4500 and 5500 and worked like a charm.

I didn't even have to apply any force, it came right off with a small twitch of the screwdriver
Back to top
 

3DFX Playrig:

Aerocool Strike-X Air
SuperMicro H8DAE
Dual Opteron 280 @ 2.4Ghz (4 cores)
4 x 1GB PC3200
3DFX Voodoo5 5500MAC PCI
WD 160GB ATA100/133
Diamond MonsterSound MX300
Windows2000 SP4
 
IP Logged
 
Obi-Wan_Kenobi
Ex Member


Re: V5500 heatsink tutorial.
Reply #9 - 21.05.07 at 02:09:54
 
oei do take care of your precious 3dfx gems people, we don't wan't to whitness some 3dfx casualties Lips Sealed
Back to top
 
 
IP Logged
 
ultima
God Member
*****
Offline


Always searching

Posts: 876
The Netherlands
Gender: male
Re: V5500 heatsink tutorial.
Reply #10 - 21.05.07 at 08:22:18
 
I take good care of my baby. Smiley

I used a cc between the screwdriver and the heatsink, I've let it sit outside the puter for a day in a mediocre warm room, so all moist would be off of it.

Then I cleaned it up real nicely and applied the new heatsinks to it and let it dry for a day.

After the installation, it now runs just fine. Already had it run 3 hours of benchmarks @ 190Mhz and she's doing great, no hickups, no artifacts, no nothing. Smiley
Heatsinks on the ram get warm. so they do their job, but in warm I mean warmer thenm room temp, but not much.

In 3dmark99 scores are the following:

@ 166Mhz = 10900
@ 180Mhz = 11040
@ 190Mhz = 11182

Back to top
 

3DFX Playrig:

Aerocool Strike-X Air
SuperMicro H8DAE
Dual Opteron 280 @ 2.4Ghz (4 cores)
4 x 1GB PC3200
3DFX Voodoo5 5500MAC PCI
WD 160GB ATA100/133
Diamond MonsterSound MX300
Windows2000 SP4
 
IP Logged
 
Pastor
YaBB Newbies
*
Offline


I love YaBB 1G - SP1!

Posts: 8
germanistan
Gender: male
Re: V5500 heatsink tutorial.
Reply #11 - 10.09.07 at 00:56:04
 
hi,#

another version :

you start your computer with the V5 inside
and play a while
when the card and the chips are hot or warm enough you just have to shut your pc down and twiddle the coolers from the chips...
Back to top
 
 
IP Logged
 
Chosen_One
Senior Member
****
Offline


Keeper of the BIOS-files...

Posts: 499
Germany
Gender: male
Re: V5500 heatsink tutorial.
Reply #12 - 10.09.07 at 17:37:34
 
like elfuego said...but you cannot "twiddle" the heatsink from the chip coz 3dfx used very ugly and adamantine glue...
Back to top
 
WWW  
IP Logged
 
Pastor
YaBB Newbies
*
Offline


I love YaBB 1G - SP1!

Posts: 8
germanistan
Gender: male
Re: V5500 heatsink tutorial.
Reply #13 - 10.09.07 at 20:38:42
 
ohh,
well
the next time i will read all posts more intense^^
Back to top
 
 
IP Logged
 
gdonovan
YaBB Administrator
*****
Offline


Infernal Collector

Posts: 2361
Re: V5500 heatsink tutorial.
Reply #14 - 10.09.07 at 21:28:37
 
Quote:
This is the first time I hear about fridge method, I heard about something else.



Freezer works best, see my video here-

http://www.youtube.com/watch?v=5kGhIg58zOY

15 minutes in the freezer works great.
Back to top
 

Rampage is alive!
 
IP Logged
 
Pages: 1 2 
Send Topic Print