3dfx Archive

レイレイ YaBB Newbies Offline o^_^o Posts: 30 Gender:	486 28.06.08 at 08:49:03 Has anyone dealt with using Voodoo hardware in a Socket 3 motherboard w/ 486 before? I'd like to know experiences of others beforehand first
Back to top	IP Logged

ps47 God Member Offline Keeper of the 3Dfx Helppage Posts: 988 Slovakia,central Europe Gender:	Re: 486 Reply #1 - 28.06.08 at 10:23:50 should work as long as the motherboard has pci slots (obviously).cards up to voodoo3 have been tested successfully,the performance was just enough to play UT at its lowest settings.voodoo2/banshee were the best performers,if memory serves.
Back to top	3Dfx Help Page / 3Dfx Game Guide IP Logged

gdonovan

YaBB Administrator

Offline

Infernal Collector

Posts: 2361

Re: 486
Reply #2 - 28.06.08 at 10:47:51

I tried running a Voodoo Graphics board a very long time ago in a 486 with PCI slots, it would crash the machine on drive load and I would have to wipe the hard drive and reload the OS. I never did get it to work and 3dfx documents indicate a pentium is the minimum platform required.

This was a very long time ago, long before I started collecting, I don't remember any more details aside from it was a Digital office machines desktop.

Back to top

Rampage is alive!

IP Logged

sigtau

Junior Member

Offline

I'm Obsessed with 3Dfx!!!

Posts: 86
Houston, TX USA
Gender: male

Re: 486
Reply #3 - 28.06.08 at 19:32:11

Just out of morbid curiosity, I dug out my old Socket 3 486 AMD 5x86 133 mhz computer and decided to try to get a voodoo card to work in it. I first tried a voodoo rush, but that wouldn't load after driver install. Second thing I tried was a Diamond PCI Monster Fusion (Banshee) and they wouldn't even post. Finally, I just stuck in a Voodoo 1 along side the S3 main video and the drivers installed fine on Windows ME. The reboot went fine. I fired up NFSII SE and it ran sort of OK with all detail turned down. I also tried Test Drive 4, but that bogged the system down to a crawl.

The conclusion I draw from this is that it is certainly possible to get a voodoo card running on a 486 type system. The CPU I have hardly qualifies as a true 486 processor. It is actually rated as a Pentium 75. If I really wanted to give myself a good laugh, I would drop in my 486DX 33mhz cpu and play NFS2 SE in slow motion Shocked

Back to top

IP Logged

レイレイ

YaBB Newbies

Offline

o^_^o

Posts: 30
Gender: female

Re: 486
Reply #4 - 28.06.08 at 19:56:54

sigtau wrote on 28.06.08 at 19:32:11:

Just out of morbid curiosity, I dug out my old Socket 3 486 AMD 5x86 133 mhz computer and decided to try to get a voodoo card to work in it. I first tried a voodoo rush, but that wouldn't load after driver install. Second thing I tried was a Diamond PCI Monster Fusion (Banshee) and they wouldn't even post. Finally, I just stuck in a Voodoo 1 along side the S3 main video and the drivers installed fine on Windows ME. The reboot went fine. I fired up NFSII SE and it ran sort of OK with all detail turned down. I also tried Test Drive 4, but that bogged the system down to a crawl.

heh interesting, because that's the processor I have! I also have a 486 DX4 100 to try out as well.

gdonovan wrote on 28.06.08 at 10:47:51:

I tried running a Voodoo Graphics board a very long time ago in a 486 with PCI slots, it would crash the machine on drive load and I would have to wipe the hard drive and reload the OS. I never did get it to work and 3dfx documents indicate a pentium is the minimum platform required.

woah that's over the top with problems. A CPU heat freeze was the only thing that happened to me to break my OS severely, I doubt a PCI video card would be a culprit

fyi i'm going to use a voodoo2, and attempt to play games like Sauerbraten Tongue

Back to top

« Last Edit: 28.06.08 at 19:58:15 by レイレイ »

IP Logged

gdonovan YaBB Administrator Offline Infernal Collector Posts: 2361	Re: 486 Reply #5 - 28.06.08 at 20:07:11 Soon as I would load the drivers it would freeze or freeze on the reboot and I could get no further.
Back to top	Rampage is alive! IP Logged

レイレイ YaBB Newbies Offline o^_^o Posts: 30 Gender:	Re: 486 Reply #6 - 28.06.08 at 20:22:48 Perhaps it's just sucking a lot of juice. I'm using a 230W PSU
Back to top	IP Logged

NitroX infinity YaBB Moderator Offline Posts: 1936 The Netherlands Gender:	Re: 486 Reply #7 - 28.06.08 at 22:12:30 230W is more than enough.
Back to top	My Blog IP Logged

Thandor Full Member Offline What's the fuzz all about? Posts: 226	Re: 486 Reply #8 - 29.06.08 at 00:15:41 I've seen (and played on) a Cyrix 486DX4/100 with Diamond Voodoo II. Half-Life did run but with 0,05FPS or something like that .
Back to top	Click here to see my collection of CPU's and GPU's! IP Logged

paulpsomiadis God Member Offline -=3Dfx still rox!=- Posts: 2011 Newcastle U.K. Gender:	Re: 486 Reply #9 - 29.06.08 at 00:30:21 WHOA! @レイレイ - you're going to try and play sauerbraten on a Voodoo card, ON A 486!!! Dies ist Ihre boomstick! http://sauerbraten.org/
Back to top	« Last Edit: 29.06.08 at 00:30:52 by paulpsomiadis » -=To MOD or not to MOD, that is a DUMB question - just MOD it!=-&&&&+May God stand between you and harm in all the empty places you must walk.+ IP Logged

gamma742

God Member

Offline

3Dfx Gamer

Posts: 1668
San Diego, CA USA
Gender: male

Re: 486
Reply #10 - 29.06.08 at 07:16:34

Although I had a P1-133 with my Diamond Monster Voodoo 1 card. My nephew only had a 486 DX 66MHz and He and I used to play Co-op Descent2 with the d2voodoo patch together. No issues other than his would chop like a slide show during heavy battle.

If we were in the same room (in the game), the game would slow down on my machine. We also played GLQuake.

Back to top

« Last Edit: 29.06.08 at 19:12:10 by gamma742 »

Quantum3D AAlchemy 3 Channel SwapLock/SyncLock System. Powered by VSA 100 GPUs Running in SLI Mode. 3dfx at it's Best...

IP Logged

レイレイ YaBB Newbies Offline o^_^o Posts: 30 Gender:	Re: 486 Reply #11 - 29.06.08 at 08:21:34 paulpsomiadis wrote on 29.06.08 at 00:30:21: you're going to try and play sauerbraten on a Voodoo card, ON A 486!!! i've played it on worse (Cyrix6x86mx @ 80mhz)
Back to top	IP Logged

レイレイ

YaBB Newbies

Offline

o^_^o

Posts: 30
Gender: female

Re: 486
Reply #12 - 06.07.08 at 07:17:05

Holy !!! the card is working!
Games tested so far:
Unreal - 4fps
Metal Gear Solid - 5fps

I think my old sound card may be bottlenecking the entire computer because it's making doom run slow too Sad

, could swap it with an AWE32...
It could be the third party driver i'm using as well (FastVoodoo2 4.6), is it better to use the reference driver? The third party ones could have some overhead for modern processor support and features I think that the 486 doesn't need to compute with

Back to top

« Last Edit: 06.07.08 at 07:20:37 by レイレイ »

IP Logged

Thandor

Full Member

Offline

What's the fuzz all about?

Posts: 226

Re: 486
Reply #13 - 06.07.08 at 13:16:57

You can always give the old reference drivers a shot

. On my Athlon 500 I noticed the new thirdparty drivers (with Voodoo5 though) were a lot slower comparing to the latest 3dfx reference drivers. The 3dfx reference drivers did not only work better performance wise, Soldiers of Fortune ran better with them too (texture corruption during start up of the game with the third party driver).

Back to top

Click here to see my collection of CPU's and GPU's!

IP Logged

レイレイ YaBB Newbies Offline o^_^o Posts: 30 Gender:	Re: 486 Reply #14 - 07.07.08 at 08:28:05 I've switched to the latest official driver, changed ram timing from 3-2-3 to 2-1-2, set read wait state to 0 and pciclk to 4, unreal now runs 10fps and mgs runs 7ish. GLQuake's getting 30fps !
Back to top	« Last Edit: 07.07.08 at 08:28:20 by レイレイ » IP Logged

	Welcome, Guest. Please Login