3dfx Archive - 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700

trevormacro

God Member

Offline

Voodoo5k6 Gold SE, Legend
& Mystical Edition

Posts: 622
Gender: male

Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700
Reply #15 - 16.06.13 at 16:54:19

@m14radu:

I don't have any others MB with agp2x. I just have one AGP pro slot of my Tyan K7xpro but not compatible with the rampy.

I have fitted the chip in the right position. There is a mark on the rampy corner (rearside) and was putted on the lower left corner. If for some reason chip is placed in bad place, it will be burned!

Some others pictures:

@ultima:

It's private. Not from a collector.

@osckhar:

When I used my IR lasergun on each DDR, the temperature increases but on cooler NOT. Perhaps the socket and chip need to be cleaned with your Ultrasonic cleaner in alcohol isopropanol (recommanded by the 3dfx engineer).

Back to top

IP Logged

m14radu God Member Offline Take your chance ! Posts: 555 Timisoara, Romania Gender:	Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700 Reply #16 - 16.06.13 at 17:29:59 Why is the Tyan K7xpro not compatible with the rampage ? Tyan K7xpro support AGP2x/4x right ?
Back to top	IP Logged

trevormacro God Member Offline Voodoo5k6 Gold SE, Legend & Mystical Edition Posts: 622 Gender:	Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700 Reply #17 - 16.06.13 at 17:51:50 m14radu wrote on 16.06.13 at 17:29:59: Why is the Tyan K7xpro not compatible with the rampage ? Tyan K7xpro support AGP2x/4x right ? I have an AGP Pro 110 slot; supports 4X/2X AGP. I need to put in this place, right?
Back to top	IP Logged

m14radu God Member Offline Take your chance ! Posts: 555 Timisoara, Romania Gender:	Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700 Reply #18 - 16.06.13 at 18:13:56 It should work Michael.
Back to top	IP Logged

trevormacro God Member Offline Voodoo5k6 Gold SE, Legend & Mystical Edition Posts: 622 Gender:	Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700 Reply #19 - 16.06.13 at 18:26:12 m14radu wrote on 16.06.13 at 18:13:56: It should work Michael. Is this agp pro support 1,5 V for rampy?
Back to top	« Last Edit: 16.06.13 at 18:28:17 by trevormacro » IP Logged

m14radu God Member Offline Take your chance ! Posts: 555 Timisoara, Romania Gender:	Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700 Reply #20 - 16.06.13 at 18:27:17 You schould check that before with another agp card, a non 3dfx one !
Back to top	IP Logged

trevormacro God Member Offline Voodoo5k6 Gold SE, Legend & Mystical Edition Posts: 622 Gender:	Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700 Reply #21 - 16.06.13 at 18:38:12 m14radu wrote on 16.06.13 at 18:27:17: You schould check that before with another agp card, a non 3dfx one ! Yes I have a ATI Radeon 7000 VE Family agp4x 1,5V. I will let you know.
Back to top	IP Logged

trevormacro

God Member

Offline

Voodoo5k6 Gold SE, Legend
& Mystical Edition

Posts: 622
Gender: male

Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700
Reply #22 - 16.06.13 at 18:51:34

gdonovan wrote on 16.06.13 at 14:28:03:

osckhar wrote on 15.06.13 at 21:46:13:

@Michel,
Just starts for using pci.exe SW and see if card is detected via 3Dfx ID vendor.

Regards,
Oscar.

I would try a 1999-2000 vintage system (AGP x 2 is fine for testing) go into the BIOS and disable all video related shadowing and caching and use a NON-3dfx PCI video card to boot up with the PCI board indicated as the primary video adapter in the BIOS.

use PCI.exe and see if a device with vender id 121a is present, this will tell you if the Rampage board is live or not.

Perhaps I need to put the jumper like you on the card to boot it?

http://www.3dfx.ch/gallery/d/48735-2/DSCN5650.JPG

On what pins is your jumper?

Back to top

« Last Edit: 16.06.13 at 18:54:57 by trevormacro »

IP Logged

gdonovan YaBB Administrator Offline Infernal Collector Posts: 2361	Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700 Reply #23 - 16.06.13 at 20:37:14 Quote: Perhaps I need to put the jumper like you on the card to boot it? http://www.3dfx.ch/gallery/d/48735-2/DSCN5650.JPG On what pins is your jumper? If you look close at the picture, the jumper is in the off postion, its just being stored on one pin.
Back to top	Rampage is alive! IP Logged

osckhar

God Member

Offline

www.3Dfx.es

Posts: 812
SPAIN
Gender: male

Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700
Reply #24 - 17.06.13 at 12:22:28

Quote:

@osckhar:

When I used my IR lasergun on each DDR, the temperature increases but on cooler NOT. Perhaps the socket and chip need to be cleaned with your Ultrasonic cleaner in alcohol isopropanol (recommanded by the 3dfx engineer).

I only hope the rampage chip always have been placed on the right position since it would be burn. Chip only has ONE position. if some one 'playing' to put/unpunt chip can place it wrong position.

Test socket works with 'springs' pins in each side of the socket. If for some reason any 'spring' is locked can cause fails on the board for bad contact.

- Oscar.

Back to top

3Dfx Site - Museo 3Dfx - 3Dfx Collection.&&

IP Logged

trevormacro God Member Offline Voodoo5k6 Gold SE, Legend & Mystical Edition Posts: 622 Gender:	Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700 Reply #25 - 17.06.13 at 17:20:32 Tyan MB tested with the rampy without luck too Rampy in route at Oscar's home. Stay tuned. Surprises not ends here.
Back to top	« Last Edit: 17.06.13 at 17:52:39 by trevormacro » IP Logged

ultima God Member Offline Always searching Posts: 876 The Netherlands Gender:	Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700 Reply #26 - 17.06.13 at 19:34:40 I have a load of different motherboards on which the card can be tested, ranging from socket 7 till socket 939 and almost all in between, so if needed, just let me know, ok??
Back to top	3DFX Playrig: Aerocool Strike-X Air SuperMicro H8DAE Dual Opteron 280 @ 2.4Ghz (4 cores) 4 x 1GB PC3200 3DFX Voodoo5 5500MAC PCI WD 160GB ATA100/133 Diamond MonsterSound MX300 Windows2000 SP4 IP Logged

m14radu God Member Offline Take your chance ! Posts: 555 Timisoara, Romania Gender:	Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700 Reply #27 - 17.06.13 at 19:54:15 Surprises not ends here ? Comme on Michael, what is the next 3dfx card ?
Back to top	IP Logged

osckhar

God Member

Offline

www.3Dfx.es

Posts: 812
SPAIN
Gender: male

Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700
Reply #28 - 20.06.13 at 15:40:00

Hello,

Package came in today.

Yupe, I also own a SPECTER 1000 agp test socket card. More than 3 years to close the deal. Card came in just 1-2 month ago (crazy and hard deal). Cool

My Rampy works ok just some problems in the interfce memory.

At the moment Michel's Rampage has some problems.

STATUS:

Card is bended (perhaps it can be the cause the test socket does not make good contact).
Rampage chip has 2 missing balls.

Add those 2 balls will not be poblem since pad is still present. I need to check if size ball is 0.76mm.

More test later.

Regards,
Oscar.

Back to top

« Last Edit: 20.06.13 at 16:13:24 by osckhar »

3Dfx Site - Museo 3Dfx - 3Dfx Collection.&&

IP Logged

trevormacro God Member Offline Voodoo5k6 Gold SE, Legend & Mystical Edition Posts: 622 Gender:	Re: 3dfx Specter 1000 AGP TEST SOCKET Rev.A1 4700 Reply #29 - 20.06.13 at 16:17:50 My website is updated. I have found one other rampage chip and Rampage test vehicles chips. News suprises inside: http://www27.brinkster.com/trevormacro/specter1000/rampage.html Take a look and enjoy
Back to top	IP Logged

	Welcome, Guest. Please Login