3dfx Archive - Canopus V2 SLI cable

	Welcome, Guest. Please Login

Home

Help

3dfx Archive › General Section › General Discussion › Canopus V2 SLI cable

(Moderators: gdonovan, NitroX infinity, FalconFly)

‹ Previous Topic | Next Topic ›

Pages: 1

Canopus V2 SLI cable (Read 137 times)

RaverX God Member Offline Voodoo2 fan Posts: 533 Oradea, Romania Gender:	Canopus V2 SLI cable 15.11.08 at 01:04:22 Did anyone here have a setup of 2 canpous v2 ? I have 2 of those card, but connecting them through normal SLI cable it's a problem, I can't figure how to connect them and still be able to install in the slots, one of the cards always gets upside down
Back to top	IP Logged

exxe God Member Offline ^^ Posts: 1316 germany	Re: Canopus V2 SLI cable Reply #1 - 15.11.08 at 09:09:33 canopus use a longer cable
Back to top	IP Logged

gamma742 God Member Offline 3Dfx Gamer Posts: 1668 San Diego, CA USA Gender:	Re: Canopus V2 SLI cable Reply #2 - 16.11.08 at 03:28:38 I made my own from a floppy cable. They need the same twist in the middle 4 pins as the standart SLI cable.
Back to top	Quantum3D AAlchemy 3 Channel SwapLock/SyncLock System. Powered by VSA 100 GPUs Running in SLI Mode. 3dfx at it's Best... IP Logged

Tim God Member Offline Posts: 1065 Gender:	Re: Canopus V2 SLI cable Reply #3 - 18.11.08 at 01:21:46 Do you need a special tool for that? To convert a floppy cable?
Back to top	IP Logged

gamma742 God Member Offline 3Dfx Gamer Posts: 1668 San Diego, CA USA Gender:	Re: Canopus V2 SLI cable Reply #4 - 18.11.08 at 02:08:23 No you just have to be careful when taking the connector off. I re-used the same connector.
Back to top	Quantum3D AAlchemy 3 Channel SwapLock/SyncLock System. Powered by VSA 100 GPUs Running in SLI Mode. 3dfx at it's Best... IP Logged

Tim God Member Offline Posts: 1065 Gender:	Re: Canopus V2 SLI cable Reply #5 - 18.11.08 at 11:18:23 gamma742 wrote on 18.11.08 at 02:08:23: No you just have to be careful when taking the connector off. I re-used the same connector. Cool. I might be able to make one myself as well then.
Back to top	IP Logged

gamma742

God Member

Offline

3Dfx Gamer

Posts: 1668
San Diego, CA USA
Gender: male

Re: Canopus V2 SLI cable
Reply #6 - 20.11.08 at 05:33:52

When you crimp the connector back together it splices into the cable. I use a pair of pliers with a soft cloth in the jaws to keep the pliers from digging in and marking up the connectors. Just gently squeeze the connector back together. They're not hard to make. I've seen some selling on eBay but I can't see how you can make any money at it. I guess they're just trying to build up their feedback Roll Eyes

Quantum3D AAlchemy 3 Channel SwapLock/SyncLock System. Powered by VSA 100 GPUs Running in SLI Mode. 3dfx at it's Best...

IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›

« Home

‹ Board

Top of this page