3dfx Archive - SB100 Shade rework.

	Welcome, Guest. Please Login

Home

Help

3dfx Archive › General Section › General Discussion › SB100 Shade rework.

(Moderators: NitroX infinity, gdonovan, FalconFly)

‹ Previous Topic | Next Topic ›

Pages: 1

SB100 Shade rework. (Read 258 times)

Tim

God Member

Offline

Posts: 1065
Gender: male

SB100 Shade rework.
02.11.10 at 11:24:40

I got my 100SB in yesterday, unfortunately I have not had the time yet to take pictures, but on one of my shades there is a small rework. I'm just wondering who else has got that.

http://www.tdfx.de/pic/shade_01.JPG

(That's exxe's shade btw, just for reference)

The R13 capacitor is only soldered to the lower pad, and then with a wire connected to the tantalum capacitor right next to it.

I will try to get some pictures of it on wednesday.

« Last Edit: 02.11.10 at 11:25:02 by Tim »

IP Logged

exxe God Member Offline ^^ Posts: 1316 germany	Re: SB100 Shade rework. Reply #1 - 02.11.10 at 16:54:17 there is also a bIG version http://www.tdfx.de/pic/shade_01b.JPG for all how searching and searching, its on the right edge near the missing corner what PCB date did your shade have?
Back to top	IP Logged

paulpsomiadis God Member Offline -=3Dfx still rox!=- Posts: 2011 Newcastle U.K. Gender:	Re: SB100 Shade rework. Reply #2 - 02.11.10 at 17:45:44 Umm...that's R13 RESISTOR. R = Resistor C = Capacitor
Back to top	-=To MOD or not to MOD, that is a DUMB question - just MOD it!=-&&&&+May God stand between you and harm in all the empty places you must walk.+ IP Logged

Tim God Member Offline Posts: 1065 Gender:	Re: SB100 Shade rework. Reply #3 - 02.11.10 at 17:48:58 Sorry, resistor, naturally. I will have a look at the dat tomorrow exxe.
Back to top	« Last Edit: 02.11.10 at 17:49:30 by Tim » IP Logged

Tim God Member Offline Posts: 1065 Gender:	Re: SB100 Shade rework. Reply #4 - 05.11.10 at 10:25:40 Tried to have a look yesterday, but I can't get the shade off, on there too tight. The whole board was flexing and that's what when I said, forget it.
Back to top	IP Logged

NitroX infinity YaBB Moderator Offline Posts: 1936 The Netherlands Gender:	Re: SB100 Shade rework. Reply #5 - 05.11.10 at 20:17:40 How did you try to get them of? By pulling them? Try laying the board on a flat surface, put two protective parts (old creditcards) between the shade module and the main board and put a flat screwdriver between those. Then try to wiggle it loose.
Back to top	My Blog IP Logged

Tim

God Member

Offline

Posts: 1065
Gender: male

Re: SB100 Shade rework.
Reply #6 - 05.11.10 at 21:16:24

NitroX infinity wrote on 05.11.10 at 20:17:40:

How did you try to get them of? By pulling them?

Try laying the board on a flat surface, put two protective parts (old creditcards) between the shade module and the main board and put a flat screwdriver between those. Then try to wiggle it loose.

They are kept in place by little plastic connectors, you need to push the two sides together then push them through, it's a right pain. Mercury brick is 10x easier lol.

Anyway, I'm not too fussed. As long as it works, it's not a prototype shade anyway I don't think.

IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›

« Home

‹ Board

Top of this page