Welcome, Guest. Please Login 3dfx Archive
 
  HomeHelpSearchLogin  
 
Page Index Toggle Pages: 1
Send Topic Print
Voodoo3 3000 AGP - AGP slot requirements (Read 350 times)
LuxKiller65
God Member
*****
Offline



Posts: 680
Luxembourg
Gender: male
Voodoo3 3000 AGP - AGP slot requirements
15.06.05 at 18:49:56
 
I remember reading somewhere that the V3 3k AGP needed some old kind of AGP voltage to work. How do I check the voltage of my AGP slot? I have a mobo originally made for PIIs (slot 1) and an AGP PRO slot (if I remember right).

Thanks
Back to top
« Last Edit: 15.06.05 at 18:50:19 by LuxKiller65 »  
WWW  
IP Logged
 
ps47
God Member
*****
Offline


Keeper of the 3Dfx Helppage

Posts: 988
Slovakia,central Europe
Gender: male
Re: Voodoo3 3000 AGP - AGP slot requirements
Reply #1 - 15.06.05 at 20:39:03
 
basically,if you can plug the voodoo3 in your agp slot,it will work Wink
Back to top
« Last Edit: 15.06.05 at 20:39:37 by ps47 »  
296989413  
IP Logged
 
Eye-Q
God Member
*****
Offline



Posts: 522
Germany
Gender: male
Re: Voodoo3 3000 AGP - AGP slot requirements
Reply #2 - 15.06.05 at 22:55:18
 
Not always...

All current Mainboards with AGP have bars which prevent old cards from being installed but the first Pentium 4-Boards with Intel-chipsets had universal AGP-slots although they only supported AGP4x/1.5 V.
Back to top
 
 
IP Logged
 
LuxKiller65
God Member
*****
Offline



Posts: 680
Luxembourg
Gender: male
Re: Voodoo3 3000 AGP - AGP slot requirements
Reply #3 - 16.06.05 at 11:22:25
 
Thanks you all. So I nedd to check my mobo if it says something before right?
Back to top
 
WWW  
IP Logged
 
NitroX infinity
YaBB Moderator
*****
Offline



Posts: 1936
The Netherlands
Gender: male
Re: Voodoo3 3000 AGP - AGP slot requirements
Reply #4 - 16.06.05 at 11:41:21
 
No, you need to look at your AGP slot and see if it looks like either A or C in the image Thandor posted.

If you have an Intel motherboard than you must be sure it's A.

These are the only two AGP slots on which your V3 will work. Smiley
Back to top
 
WWW  
IP Logged
 
LuxKiller65
God Member
*****
Offline



Posts: 680
Luxembourg
Gender: male
Re: Voodoo3 3000 AGP - AGP slot requirements
Reply #5 - 16.06.05 at 15:10:05
 
just checked. It is an Intel mobo and the AGP connector looks like the "A". It is a PII-based mobo, will the V3 3k AGP work?

Thanks
Back to top
« Last Edit: 16.06.05 at 15:10:40 by LuxKiller65 »  
WWW  
IP Logged
 
gdonovan
YaBB Administrator
*****
Offline


Infernal Collector

Posts: 2361
Re: Voodoo3 3000 AGP - AGP slot requirements
Reply #6 - 16.06.05 at 15:56:39
 
Quote:
As far as I know the motherboards with an Intel 440BX chipset are compatible since they have an AGP2x connector.




BX/LX/ZX board won't give you any problems, I have been running them for years.
Back to top
 

Rampage is alive!
 
IP Logged
 
LuxKiller65
God Member
*****
Offline



Posts: 680
Luxembourg
Gender: male
Re: Voodoo3 3000 AGP - AGP slot requirements
Reply #7 - 16.06.05 at 17:38:21
 
It's an AL440LX.

Tongue

Thanks guys, now I'm sure it's gonna work!

Wink
Back to top
 
WWW  
IP Logged
 
LuxKiller65
God Member
*****
Offline



Posts: 680
Luxembourg
Gender: male
Re: Voodoo3 3000 AGP - AGP slot requirements
Reply #8 - 25.06.05 at 08:59:45
 
I'm bored so I decided to do this screenshot, to kill some time...

...

This mobo rocks!
Back to top
 
WWW  
IP Logged
 
Thandor
Ex Member
***


What's the fuzz all about?

Re: Voodoo3 3000 AGP - AGP slot requirements
Reply #9 - 28.06.05 at 02:27:36
 
Bear in mind that not all AGP4x cards are compatible with AGP8x.

Some examples of cards that look like an universal AGP4x card but are AGP2x cards in reality :
- ATI Rage Fury Maxx - Rage 128 pro
- Diamond Stealth III s540 Extreme
- Diamond Viper V770, Revision A, NVidia TNT2
- Diamond Viper II z200 Savage 2000
- Elsa Erazor III (100 ohms)
- Hercules 3D Prophet 4500
- Leadtek WinFast 3D S320 II, Revision A, NVidia TNT2
- S3 Savage4 lager revision 3.0 or lower
- SIS 305 32MB
- SiS 6326
- VideoLogic Vivid! XS (Kyro II)

-=[How to find out wheter your card uses 3,3V or 1,5V]=-
Stuff you need to complete this practicum
  • Multimeter
  • AGP Grahpics card

    Lay the card down with the backside facing upwards.
    At that point you're looking at the back of the card.
    Set the multimeter to measure Ohm. Also known as resistance.
    ...
    Picture 1, Multimeter set to Ohm. You can see the display shows '1' since the needles aren't connected to each other. This means there is no connection.

    Put one needle of the multimeter on Pin A2 of the AGP Card. Pin A2 is the second pin when looking from right to the left.
    On 'picture 2' you can see Pin A2, it's colored in red.
    ...
    Picture 2, Pin A2 marked in red

    Put the other needle on the backplate of the card. On 'picture 3' you can see more details.
    The backplate of the card is usually connected with the 'Ground'

    ...
    Picture 3, the backplate of the card.

    If there's no connection between Pin A2 and 'Ground' the multimeter will display '1'. This means we're dealing with an AGP 3,3V card. If the multimeter shows '0' we have an AGP 1,5V card.
  • Back to top
    « Last Edit: 29.06.05 at 15:26:35 by Thandor »  
     
    IP Logged
     
    LuxKiller65
    God Member
    *****
    Offline



    Posts: 680
    Luxembourg
    Gender: male
    Re: Voodoo3 3000 AGP - AGP slot requirements
    Reply #10 - 28.06.05 at 16:24:16
     
    Aw gosh that's too technical for me man!

    Just want to be sure my V3 can work on this mobo!

    ^^'''''''''''''''
    Back to top
     
    WWW  
    IP Logged
     
    kaneda
    Guest


    Re: Voodoo3 3000 AGP - AGP slot requirements
    Reply #11 - 28.06.05 at 18:00:34
     
    just a  quick question how you ppl know that the L card of powercolor isnt 1.5v?...
    Back to top
     
     
    IP Logged
     
    Obi-Wan_Kenobi
    Ex Member


    Re: Voodoo3 3000 AGP - AGP slot requirements
    Reply #12 - 28.06.05 at 18:04:45
     
    there are alot of tests been made, so that would figure out how hehe. Grin anyway it has been tested on 1.5V boards, and it didn't work the way it should do, the system hangen and so on. That is one of the main things it only works in 3.3volt boards.
    Back to top
    « Last Edit: 28.06.05 at 18:06:22 by N/A »  
     
    IP Logged
     
    gdonovan
    YaBB Administrator
    *****
    Offline


    Infernal Collector

    Posts: 2361
    Re: Voodoo3 3000 AGP - AGP slot requirements
    Reply #13 - 28.06.05 at 21:58:07
     
    Quote:
    just a  quick question how you ppl know that the L card of powercolor isnt 1.5v?...


    Simple, I tested it.
    Back to top
     

    Rampage is alive!
     
    IP Logged
     
    Page Index Toggle Pages: 1
    Send Topic Print