Welcome, Guest. Please Login 3dfx Archive
 
  HomeHelpSearchLogin  
 
Pages: 1 2 3 4
Send Topic Print
Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x (Read 2601 times)
Komponent
Senior Member
****
Offline


3dfx modder

Posts: 282
Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
30.10.13 at 20:46:56
 
I had some free time this evening, so I thought I'd look into a mod I was asked for: Voodoo5 5500 AGP working with 1.5v signaling (the so called AGP4x).
In the picture you have the instructions to replicate what I've come up with:

...

I only have available a motherboard with Universal AGP 2.0, but I measured the working voltage and it was 1.5v. Tested under Windows ME for a number of 3DMark2001SE runs, Fastest FSAA setting, no problems.

TESTERS NEEDED!
If some of you lads with AGP 4x only motherboards could please copy this mod on a Voodoo5 card and test for compatibility would be great. There are 3 ways to make possible the insertion of a Voodoo5 into a 4x keyed AGP slot: use an universal AGP riser, remove the notch from the motherboard slot or cut a key into the Voodoo5's PCB.
Warning: this mod converts the Voodoo5 AGP from 3.3v only operation to 1.5v signaling only. I will probably refine it over the weekend to include jumpers to select between the two modes.
Back to top
« Last Edit: 30.10.13 at 20:58:17 by Komponent »  
 
IP Logged
 
Loeschzwerg
Senior Member
****
Offline


AAlchemy PSU maker :-)

Posts: 396
Germany -> Bavaria -> Augsburg
Gender: male
Re: Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
Reply #1 - 30.10.13 at 22:09:21
 
Ok, I understand the pin C1 and AGP A2 modification, that's what I did too. (didn't work)

But why connect B16 directly to AGP B7? It's base clock signal (66MHz) I know, but what's the deal with it. Enlighten me please Smiley

Back to top
 
 
IP Logged
 
Komponent
Senior Member
****
Offline


3dfx modder

Posts: 282
Re: Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
Reply #2 - 31.10.13 at 04:38:08
 
Rerouting to bypass the AND gate IC that does not work with 1.5v.
Back to top
 
 
IP Logged
 
Loeschzwerg
Senior Member
****
Offline


AAlchemy PSU maker :-)

Posts: 396
Germany -> Bavaria -> Augsburg
Gender: male
Re: Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
Reply #3 - 31.10.13 at 06:52:27
 
Ah ok, makes sense. Thanks Smiley Still wondering what this gate is meant for. Many early V5 prototypes don't have it.

Test following this afternoon when I'm home from work.
Back to top
 
 
IP Logged
 
m14radu
God Member
*****
Offline


Take your chance !

Posts: 555
Timisoara, Romania
Gender: male
Re: Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
Reply #4 - 31.10.13 at 08:15:16
 
You did it Komponent !
Congratulation...seems to be to easy Smiley after so many attempts ...
Back to top
 
WWW m14radu  
IP Logged
 
osckhar
God Member
*****
Offline


www.3Dfx.es

Posts: 812
SPAIN
Gender: male
Re: Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
Reply #5 - 31.10.13 at 09:18:32
 
Amazing komponent! Finally you got it. Not words here.  Cheesy
Back to top
 
WWW  
IP Logged
 
EMPEROR
Junior Member
**
Offline


3dfx enthusiast

Posts: 67
Germany
Gender: male
Re: Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
Reply #6 - 31.10.13 at 10:52:35
 
If this mod is really working, this is one of the best mods ever done! Great job komponent!!!
Back to top
 
disharmoniser https://www.facebook.com/lachezar.stefanov.35  
IP Logged
 
osckhar
God Member
*****
Offline


www.3Dfx.es

Posts: 812
SPAIN
Gender: male
Re: Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
Reply #7 - 31.10.13 at 16:38:29
 
MOD done. Just tested kt333 board. Card boots up Vagp 1.5. Now testing 3Dmark test. System is 100% stable.

...

I would need an agp riser to test it in a pure agp4x.

Great job again komponent.

Regards,
Oscar.
Back to top
« Last Edit: 31.10.13 at 17:34:21 by osckhar »  
WWW  
IP Logged
 
m14radu
God Member
*****
Offline


Take your chance !

Posts: 555
Timisoara, Romania
Gender: male
Re: Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
Reply #8 - 31.10.13 at 16:43:25
 
Cheesy Cheesy Cheesy
Back to top
 
WWW m14radu  
IP Logged
 
goriath
God Member
*****
Offline


Ruggedized Retro Gamer

Posts: 599
Italy/Slovenija
Gender: male
Re: Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
Reply #9 - 31.10.13 at 17:31:52
 
osckhar wrote on 31.10.13 at 16:38:29:
MOD done. Just tested kt333 board. Card boots up Vagp 1.5. Now testing 3Dmark test. System is 100% stable.

I would need an agp riser to test it in a pure agp4x.

Great job again komponent.

Regards,
Oscar.


Try to add a jumper on the A2-C1 track.
After I put a jumper there it's not working anymore.
Reinstalled the 4.7KOhm resistor in R22 and it's working again.

BTW this mod need two jumpers/microswitches to be reversible, one in the R46 the other on the C1-GND track.
Back to top
« Last Edit: 31.10.13 at 18:16:10 by goriath »  

...
OLD SCHOOL: Because it was done right the first time
 
IP Logged
 
osckhar
God Member
*****
Offline


www.3Dfx.es

Posts: 812
SPAIN
Gender: male
Re: Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
Reply #10 - 31.10.13 at 18:26:22
 
@goriath,
Once you connected A2toC1 card stop to work?

Now I have connected A2toGND

Regards,
Oscar.
Back to top
 
WWW  
IP Logged
 
Komponent
Senior Member
****
Offline


3dfx modder

Posts: 282
Re: Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
Reply #11 - 31.10.13 at 18:33:02
 
@goriath
Sorry, I don't understand. Shocked
Let aside jumpers for now. Follow exactly my instructions. It really should work.
Back to top
 
 
IP Logged
 
Loeschzwerg
Senior Member
****
Offline


AAlchemy PSU maker :-)

Posts: 396
Germany -> Bavaria -> Augsburg
Gender: male
Re: Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
Reply #12 - 31.10.13 at 19:12:39
 
Can confirm card is booting on AGP 2.0 board with 4x/8x notched slot. System is an Asus A8V Deluxe.

I'm using an AGP riser.

Card is NOT running stable at the moment, the system freezes on the second/third 3DMark99 test.

Going to check the AGP connection, riser cards are always a bit wobbly.
Back to top
« Last Edit: 31.10.13 at 19:15:33 by Loeschzwerg »  
 
IP Logged
 
Loeschzwerg
Senior Member
****
Offline


AAlchemy PSU maker :-)

Posts: 396
Germany -> Bavaria -> Augsburg
Gender: male
Re: Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
Reply #13 - 01.11.13 at 21:12:57
 
Couldn't get the card running stable in 3d applications. Flashed the bios to 1.12 but the card didn't boot anymore after this... Unfortunately I can't get it flashed back Shocked No matter what bios, what tool version and what system I use.

So I'm going to undo the mod and try to flash it again.
Back to top
 
 
IP Logged
 
Komponent
Senior Member
****
Offline


3dfx modder

Posts: 282
Re: Voodoo5 5500 mod from 3.3v only to 1.5v only AGP4x
Reply #14 - 02.11.13 at 14:14:39
 
Video: http://youtu.be/73kUXgbTcG4

EDIT: VERY IMPORTANT UPDATE

...

For stability improvement unsolder the marked pin (pin 14 of the IC) and lift it off the pad to disable the IC (or unsolder and remove the IC).

For Windows operation compatibility improvement go to Device Manager, System Devices and locate an entry that should read "CPU to AGP controller". Select it and choose to Update Driver. Use "PCI standard PCI-to-PCI bridge" driver for it. That will disable advanced AGP features.

It is highly recommended that you apply both this updates! If you tried the mod before ad encountered problems in operation, do the above 2 things and give it another spin.

I need your feedback if you want me to further refine the mod.
Over the years I've come up with a sh1t load of world premiere mods and I've received little credit or support (I wonder why I'm still doing it?), but at least feedback is of the essence.
Back to top
« Last Edit: 02.11.13 at 15:54:48 by Komponent »  
 
IP Logged
 
Pages: 1 2 3 4
Send Topic Print