Welcome, Guest. Please Login 3dfx Archive
 
 
  HomeHelpSearchLogin  
 
  3dfx Archive › 3dfx Section › Tech Talk › Legacy PC doesn´t boot !
(Moderators: FalconFly, gdonovan, NitroX infinity)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1
Send Topic Print
Legacy PC doesn´t boot ! (Read 175 times)
Nagual
YaBB Newbies
*
Offline


Searching for the perfect
driver !

Posts: 12
Rio de Janeiro - BR
Gender: male
Legacy PC doesn´t boot !
31.08.06 at 18:57:19  
Well, I keep an old desktop just to play some games in Glide, officing, etc.  But since I´ve replaced the cd-rom drive by a new one, from Benq, it doesn´t boot any more.  I have checked the cd-rom jumper, the flat cable, the setup, the cd-rom itself, and updated the firmware,  but it always stops at the same point after the post.  When I take the drive off,  I get to windows fast.  Just didn´t update the bios yet.
                             ??? ??? ??? 
Need some support.
Thanks a lot !

specs.: Old FIC motherboard, OEM made to HP/Pentium 350-Slot1/Voodoo 4500 AGP/2x128MB RAM/OPTI ISA Sound Card/Samsung 4GB/Windows98
Back to top
 
Athlon TB 1700+@2011Mhz/Zalman CNPS6000/Abit NF7-S 2.0/Maxxtro 500(?)Watts/2x256MB DDR400/ATI Radeon 9550 256MB/Seagate Barracuda 80GB/Audigy SE /WinXP-Pro SP1
 
IP Logged
 
gamma742
God Member
*****
Offline


3Dfx Gamer

Posts: 1668
San Diego, CA  USA
Gender: male
Re: Legacy PC doesn´t boot !
Reply #1 - 01.09.06 at 05:24:58  
Have you tried putting the CDrom on the other IDE (2)

This way it won't conflict with your H.D.D. I'm thinking that it an old Harddrive, maybe mode 4 and the CDrom is a newer Ultra ATA.

Make each one the master and put them on seperate cables.
Back to top
 
Quantum3D AAlchemy 3 Channel SwapLock/SyncLock System.  Powered by VSA 100 GPUs Running in SLI Mode. 3dfx at it's Best......
gamma742 https://www.facebook.com/bob.waller  
IP Logged
 
gamma742
God Member
*****
Offline


3Dfx Gamer

Posts: 1668
San Diego, CA  USA
Gender: male
Re: Legacy PC doesn´t boot !
Reply #2 - 01.09.06 at 05:26:54  
Oh yeah. Don't forget to set your BIOS to AUTO for the IDE 1 MASTER and IDE 2 MASTER.
Back to top
 
Quantum3D AAlchemy 3 Channel SwapLock/SyncLock System.  Powered by VSA 100 GPUs Running in SLI Mode. 3dfx at it's Best......
gamma742 https://www.facebook.com/bob.waller  
IP Logged
 
Nagual
YaBB Newbies
*
Offline


Searching for the perfect
driver !

Posts: 12
Rio de Janeiro - BR
Gender: male
Re: Legacy PC doesn´t boot !
Reply #3 - 01.09.06 at 13:31:10  
Thank you gamma, but they already are on separated cables,  as masters.  I think I´m gonna update the bios. I haven´t donne this yet  because the board was takken from a Hewllet Packard desktop, and they used to be some kind of tricky.  Besides,   the only information I have about the bios update is that it gives support to WinXP.  Well,  it´s not much..., but it must be different...
                                           Undecided
Back to top
 
Athlon TB 1700+@2011Mhz/Zalman CNPS6000/Abit NF7-S 2.0/Maxxtro 500(?)Watts/2x256MB DDR400/ATI Radeon 9550 256MB/Seagate Barracuda 80GB/Audigy SE /WinXP-Pro SP1
 
IP Logged
 
jandarsun8
God Member
*****
Offline



Posts: 712
Minneapolis, MN
Gender: male
Re: Legacy PC doesn´t boot !
Reply #4 - 01.09.06 at 15:29:16  
The new cd rom works in a different pc? I've gotten a bad one out of the box before, might want to try that. 
Back to top
« Last Edit: 01.09.06 at 15:31:37 by jandarsun8 »  
Dallizzt2004  
IP Logged
 
Page Index Toggle Pages: 1
Send Topic Print
‹ Previous Topic | Next Topic ›
  « Home ‹ Board Top of this page

3dfx Archive » Powered by YaBB 2.4!
YaBB © 2000-2009. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge